Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 306
2012-04-05
Video
Learn how the U.S. Department of Energy's Clean Cities Program can help with the deployment of alternative fuel and advanced technology school buses. Presenter Mark S. Smith, US Department of Energy
2012-03-31
Video
Toyota is committed to the development of advanced powertrains to help address concerns with future oil supplies, the impacts of increased carbon dioxide emissions, and air pollution. Towards that end Toyota is planning to bring to market in 2012 a plug-in hybrid vehicle, a short range electric vehicle, a long range electric vehicle and in the 2015 timeframe hydrogen powered fuel cell vehicle. This presentation will focus on our electric vehicle plans and the challenges with bringing electric vehicle to the market. From the 2010 Alt Fuels Study, Toyota has identified that two key barriers for EV adoption are the times to charge the vehicle, and electricity cost. The study finds that the current infrastructure could be sufficient for most driving needs but EV drivers will still need to alter their driving habits slightly.
2012-03-29
Video
Wireless power transfer (WPT) of plug-in and battery electric vehicles (PEV�s) rely on loosely coupled transformer operating in magnetic resonance to tune out reactive effects. Depending on the degree of coupling, such systems experience a single peak response that trends to bifurcate as the coefficient of coupling increases. This places additional burden on the WPT grid side power controller to not only manage the power transfer process but to manage the transmit coil to receiver coil reactive power in response to vehicle ground clearance and misalignment tolerance. In addition, the WPT rectified output voltage must dynamically match the vehicle on-board regenerative energy storage system (RESS). This paper examines the essentials of WPT operation and challenges facing the commercialization of wireless charging. Experimental results obtained from the Oak Ridge National Laboratory WPT apparatus are presented as validation of the theory. Presenter John Miller, ORNL
2012-03-29
Video
What are the requirements of customers in an urban environment? What will sustainable mobility look like in the future? This presentation gives an overview of the integrated approach used by BMW to develop the BMW i3 - a purpose-built battery electric vehicle. Very low driving resistances for such a vehicle concept enable the delivery of both impressive range and driving excitement. A small optional auxiliary power unit offers range security for unexpected situations and opens up BEVs to customers who are willing to buy a BEV but are still hesitant due to range anxiety. Additional electric vehicles sold to the formerly range anxious will create additional electric miles. Presenter Franz Storkenmaier, BMW Group
2012-03-29
Video
Battery Electric Vehicles and Extended Range Electric Vehicles, like the Chevrolet Volt, can use electrical energy from the Grid to meet the majority of a driver�s transportation needs. This has the positive societal effects of displace petroleum consumption and associated pollutants from combustion on a well to wheels basis, as well as reduced energy costs for the driver. CO2 may also be lower, but this depends upon the nature of the grid energy generation. There is a mix of sources � coal-fired, gas -fired, nuclear or renewables, like hydro, solar, wind or biomass for grid electrical energy. This mix changes by region, and also on the weather and time of day. By monitoring the grid mix and communicating it to drivers (or to their vehicles) in real-time, electrically driven vehicles may be recharged to take advantage of the lowest CO2, and potentially lower cost charging opportunities.
2012-03-29
Video
Nissan Motor Company has recently released the �Nissan Green Program 2016� which is a six-year action plan embodying the company�s environmental philosophy: Symbiosis of People, Vehicles and Nature. One of the key activities of this Program is the successful penetration of Zero-Emission Vehicles into the market which includes electric vehicle (EV) cumulative sales of 1.5M units with our Alliance partner Renault, introduction of a fuel cell electric vehicle (FCEV) into the market, taking a global leadership in supplying batteries for electric drive and creating zero-emission societies. This presentation will highlight some of these key activities. Presenter Kev Adjemian, Nissan Technical Center NA
2012-03-29
Video
The Idaho National Laboratory is collecting data from grid-connected electric drive vehicles and charging infrastructure that have been deployed across the United States in five large-scale demonstrations funded by the U.S. Department of Energy. These demonstrations include The EV Project infrastructure demonstration, led by ECOtality North America; Coulomb Technologies� ChargePoint America infrastructure demonstration; General Motors� Chevrolet Volt extended range electric vehicle demonstration; Chrysler�s Ram plug-in hybrid electric vehicle demonstration; and the Ford Escape plug-in hybrid electric vehicle advanced research fleet demonstration. This presentation describes real-world vehicle and charging infrastructure usage observed during the early stages of these demonstrations. Presenter John Smart, Idaho National Lab.
2012-03-29
Video
The Focus Electric is Ford�s first full-featured 5 passenger battery electric vehicle. The engineering team set our sights on achieving best-in-class function and efficiency and was successful with an EPA certified 1XX MPGe and range XXX then the facing competition allowing for a slightly lower capacity battery pack and larger vehicle without customer trade-off. We briefly overview the engineering method and technologies employed to deliver the results as well as sharing some of the functional challenges unique to this type of vehicle. Presenter Charles Gray, Ford Motor Co.
2012-03-29
Video
Seven different suppliers will discuss their latest technologies. Panelist Jon Bereisa, Auto Lectrification LLC John Burgers, Dana Canada Corporation Derek De Bono, Valeo Dusan Graovac, Infineon Technologies AG Ronald P. Krupitzer, American Iron and Steel Institute Timothy J. Lawler, Bosch Corp. Ian M. Sharp, Flybrid Systems LLP
2012-03-29
Video
Several technological advancements have enabled hybrid technology to become a viable option in the commercial truck market. Although hybrid trucks are becoming more mainstream, they are not the right alternative fuel solution for every application. When matched with the right duty cycle, hybrid technology can provide a significant cost savings. Due to these advancements and anticipated benefits, hybrid commercial trucks are forecasted to become a significant part of the commercial truck market. Presenter Glenn Ellis, Hino Motors Sales USA Inc.
2012-03-29
Video
Despite significant investment by both government and industry, the electric vehicle is not achieving the market share needed to make a significant impact on carbon emissions and energy independence. This presents some particular questions to policymakers and manufacturers; how to overcome the barriers to development and adoption in a tough economic climate? how can industry be encouraged to develop electric vehicle technology that meets consumers performance and pricing needs and how can consumers be encouraged to buy? The dramatic reductions in CO2 emissions required by international law present some formidable targets that need to be met over the coming two decades. How can we accelerate EV adoption to help achieve them?
2012-03-29
Video
Vehicle electrification is shaping the future of automotive mobility in terms of automotive power and propulsion. The market for New Energy Vehicles (HEV/PHEV/REEV/EV) as well as clean vehicle technologies is expected to grow steadily driven by government regulations mandating increased fuel economy and lower emissions. The fastest growth in this market will be in Asia Pacific, most notably China. The Chinese government has made its intentions clear on how important it considers the development and consumer purchase of hybrid and electric vehicles. The mandate is that by year 2012, vehicle manufacturers produce at least 500,000 units (or 5%) per year of their total output as hybrid and/or electric. All Chinese vehicle manufacturers must have at least one HEV or EV model in the market by the same year. Thus far China has invested over US$3.5 billion to stimulate the production of NEVs and the necessary infrastructure to support them.
2012-03-27
Video
Electrification is becoming a means of sustainable transportation to address global climate change and environmental concerns by reducing the dependency on fossil fuels for personal transportation; and to use renewable energy for transportation. Ford has incorporated Electrification as an important part of the company's sustainable strategy to provide sustainable transportation that is affordable environmentally, socially and economically. While offering customers Power of Choice for a wide range of Electrification products, Ford continues to exploit the potentials of Electrification by taking advantage of the advanced information technology to create smarter and greener vehicles customers want and value. This presentation will highlight some of the on-going research and development on smart and connected Electrification. Presenter Ming Lang Kuang, Ford Motor Co.
2012-03-27
Video
From 2009 until present Toyota has had a demonstration program of Prius PHV which is comprised of 600 vehicles throughout Japan, Europe and in the US. The vehicles were given to government agencies, corporations, utility companies and private individuals to use. With these demo units Toyota wanted to understand the market reaction and real world impact of plug-in technology on gasoline displacement with increased use of electricity as a fuel. This presentation shows that approximately 50% of fuel was saved using the PHVs in the US. An experiment in Toyota City shows that if public infrastructure is optimized to be convenient and located where people normally park, there is a potential to achieve an ideal fuel savings of 61%. The demonstration program shows that plug-in technology in fact saves fuel and that the proper infrastructure can optimize the fuel savings of plug-in hybrids. Presenter Avernethy Francisco, Toyota
2012-03-27
Video
The automotive industry continues to develop new powertrain technologies aimed at reducing overall vehicle level fuel consumption. This paper discusses the development of a new highly efficient parallel hybrid transmission for use in transversely installed powertrains for FWD applications. FEV is developing a new 7-speed hybrid transmission for transverse installation. The transmission with a design torque of 320 Nm is based on AMT (automated manual transmission) technology and uses a single electric motor. The innovative gearset layout combines the advantages of modern AMTs such as best efficiency, low costs and few components (reduced part count) with full hybrid capabilities and electric torque support during all gear shifts. Furthermore, the gear set layout allows for very short shift-times due to the favorable distribution of inertias. Other features include an A/C compressor being electrically driven by the electric motor of the transmission during engine start/stop phases.
2012-03-27
Video
Over the past several years, new recommended practices for testing plug-in vehicles have been developed by SAE standards committees. At first only proprietary or prototype vehicles were available to validate new procedures. However, with the recent availability of Chevy Volt and Nissan Leaf, these test procedures were put to the test in Argonne�s National Laboratory�s dynamometer test facility. Procedures for the Volt were according to the SAE J1711 procedures. The Leaf was tested according to procedures still under development in the SAE J1634 task force. Identified were aspects of the tests that were successful and areas where more development is needed. As described in SAE J2841, the Volt results were analyzed using a �utility factor� to estimate in-use expectations of electric-only miles.
2012-03-27
Video
JLR is on track to develop stop-start, parallel hybrid and plug-in parallel hybrid vehicles in the next few years. Plug-in hybridization is arguably the most suitable technology for large, premium luxury vehicles for the foreseeable future. Range_e is a UK based demonstrator for a plug-in hybrid system and has brought into sharp focus the attribute issues and wider challenges that need to be taken into consideration when moving towards production. Presenter Paul Bostock, Jaguar Land Rover
2012-03-27
Video
Presentation will concentrate on a brief overview of SAE International including history, international focus and SAE electro-mobility ground vehicle standards development activities. The new era of mobility and the driving forces behind it including converging technologies and today�s drive toward �green� will be discussed. Also, standards and technology enablers for vehicle electrification including, the global landscape for EV charging standards and next generation charging method approaches will be reviewed. Additionally, an overview of SAE global EV Battery Standards and activities including industry/government collaborative efforts to develop lithium ion rechargeable energy storage system safety standards will be provided. Presenter Keith Wilson, SAE International
2012-03-27
Video
Automakers, suppliers, public agencies, interest groups and others are increasingly embracing the environment as one of the dominant forces in the US automotive market. All parties have a strong vested interest in understanding how environmental concerns will influence design, production, marketing and usage of tomorrow�s vehicles. A common need of all parties is independent and actionable information to enable them to make better decisions and have the greatest chance of being successful in this uncertain future. Four factors - an uncertain economic climate; a constantly changing governmental regulatory system; advancements in powertrain technology; and ever-present environmental concerns - continue to shape the automotive landscape. While automakers are focused on developing alternative powertrains and alternative fuel options for an increasingly �green� vehicle market, J.D.
2012-03-27
Video
There are now a wide variety of Hybrid and Electric Vehicles in or near production. They reduce or displace petroleum consumption with of various combinations of conventional IC engine, mechanical transmission, liquid fuel storage, electrical energy storage, electrical and electro-mechanical energy conversion, and vehicle-to-grid energy interface. These Electrified types of vehicles include Mild Hybrid, Full Hybrid, Plug-In Hybrid, Extended Range Electric, and Battery Electric. Some types differ in their actual usability for the real mixes of driving trips, and further that differ in their effectiveness to reduce or displace fuel in actual real world driving use. Vehicle size is also a factor in total vehicle utility in transporting people. If we may segment drivers by their driving needs, in each segment, we see a particular type of electrified vehicle that is better suited than others at minimizing fuel cost and petroleum consumption for the purposes of transporting people.
2012-03-27
Video
The rapid pace of recent progress in vehicle electrification technologies points to a bright future for electric-drive vehicles, but uncertainty regarding future technical trajectories and uncertainty in consumer response make possible a multitude of electric-drive vehicle futures. This presentation will examine a range of these possible electric-drive futures as a function of different technology and pricing scenarios. An exploration of initial conditions, market uptake, and resulting social benefits will show how HEV and PEV technology enable the attainment of stringent vehicle efficiency goals and unlock potential for lower-carbon futures. Presenter Jacob Ward, Department Of Energy
2012-03-27
Video
In Oct. 2011, Nissan announced its new six-year environmental plan, Nissan Green Program 2016 (NGP 2016), that includes initiatives to lead fuel efficiency: 35% fuel economy improvement compared with 2005 on a corporate average for all Nissan vehicles sold in Japan, China, Europe and the United States. To achieve this target, we`re planning to launch products delivering class-leading fuel efficiency such as an all-new FWD hybrid model, Introducing a next-generation continuously variable transmission (CVT). In this session, Nissan`s apploach for fuel erfficiency is presented with internal-conbustion powered technology evolution and hybridization, referring to new FWD hybrid system. Presenter Taiichi Onoyama, Nissan Motor Company, Ltd.
2012-03-27
Video
Hybrid Electric Drive (HED) provides the potential to improve military vehicle capabilities beyond the well understood fuel economy benefits. Additional HED benefits for military operations can be realized in the areas of mobility, survivability, lethality, power generation and maintainability. General Dynamics Land Systems (GDLS) continues to demonstrate significant advantages that HED can offer to military vehicle platforms. This presentation will focus on the advanced military capabilities provided by HED utilizing in-hub wheel motors and include a summary of GDLS demonstrator vehicles with integrated HED. Presenter Andrew Silveri, GENERAL DYNAMICS LAND SYST
2012-03-23
Video
Motor Trend Magazine�s selection of the Chevrolet Volt as its 2011 Car-Of-The-Year saw the publication inundated with responses, the vast majority of these polarized between astute praise and bewildering condemnation. Here, I will read you some of our best Volt Car-Of-The-Year reader mail. And along the way, offer a few of my own responses � including thoughts on how the gulf between these contentious camps of enthusiasts might eventually be bridged. Presenter Kim Reynolds, Motor Trend Magazine
2012-03-23
Video
This article characterizes the special features of drilling of CFRP/Titanium and -Aluminium stacks. Simplified theoretic models will show how CFRP/Titanium stacks should be machined without scratches and burn marks contacting carbon. Low axial forces and smart chip removal technology are the main characteristics of the drilling tool technology, optimized to reach H8 quality in one shot operation. Presenter Peter Mueller-Hummel, Cutting Tools Inc.
2012-03-23
Video
: Fiber Placement equipment has historically been very large and very expensive. Therefore, the AFP process has been mostly exclusive to the larger aerospace companies of the world. In order to achieve more widespread use of the AFP process, a wider variety of machine configurations must be offered and cost of the equipment must be decreased. Commercially available, articulated robotic arms have been identified as an attractive, low cost option for AFP machine platforms. However, incorporating AFP material delivery technology with robotic arms has many challenges. These challenges relate to both hardware and software issues. This presentation will address the technical challenges of using robots as a machine platform for the AFP process and review the current status of this composites lamination equipment technology. Presenter Frederic Challois, Coriolis Composites
2012-03-23
Video
In a variety of industries there is a growing need to manufacture high quality carbon fibre epoxy matrix composite structures at greater production rates and lower costs than has historically been the case. This has developed into a desire for the automation of the manufacture of components, and in particular the lay-up phase, with Automated Tape Laying (ATL) and Fibre Placement (AFP) the most popular choices. When used for large primary structures there are such potential gains to be had that both techniques have seen rapid implementation into manufacturing environments. But significant concerns remain and these have limited their wider adoption into secondary structure manufacturing, where manual forming of woven broadgoods is dominant. As a result the manufacture of secondary structures is generally explored for costs reduction through drape simulation and lower cost materials.
2012-03-23
Video
In Aeronautic industry, when we launch a new industrialization for an aircraft sub assembly we always have the same questions in mind for drilling operations, especially when focusing on lean manufacturing. How can we avoid dismantling and deburring parts after drilling operation? Can a drilling centre perform all the tasks needed to deliver a hole ready to install final fastener? How can we decrease down-time of the drilling centre? Can a drilling centre be integrated in a pulse assembly line? How can we improve environmental efficiency of a drilling centre? It is based on these main drivers that AIRBUS has developed, with SPIE and SOS, a new generation of drilling centre dedicated for hard materials such as titanium, and high thicknesses. The first application was for the assembly of the primary structure of A350 engine pylons. The main solution that was implemented meeting several objectives was the development of orbital drilling technology in hard metal stacks.
2012-03-23
Video
Hybrid vehicles in the modern era were developed with a strong primary goal to increase fuel efficiency in the North American market. Over the last 15 years, this market has expanded from zero sales to as high as 3% of total US sales. Most recently, the portfolio of competitive offerings with HEV propulsion systems has grown even more to about 30 models on sale today. Some interesting features and attributes have evolved thru this wider array of products giving the customer much more choice of which characteristics to select to match their needs. Ford�s 3rd generation HEV system will be offered for sale this fall. With it, we have continued our focus on the Fuel Efficiency as the driving force for our efforts. The overall process for the system engineering and some of the relevant subsystem and component contributors to the Fuel Efficiency improvement reflected in the 2013 Model Year Fusion and CMAX Hybrids will be presented. Presenter Charles Gray, Ford Motor Co.
2012-03-23
Video
Conventional hybrids have been marketed in the US for over a decade, with very high quality scores and high consumer satisfaction. However, their cost is still too high for mass market acceptance and their sales continue to be almost entirely to early adopters. This presentation will discuss mainstream consumer discounting of future fuel savings and how much they might be willing to pay, then focus on the potential for future hybrid efficiency improvements, synergies with other technologies, and cost reduction. The future cost reduction and efficiency benefits of the input powersplit and the P2 (parallel twin-clutch) hybrid systems are compared and projections offered through 2030. Presenter John German, International Council On Clean Transport
Viewing 121 to 150 of 306

Filter

  • Video
    306
  • Range:
    to:
  • Year: